A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
Listed here in the next paragraph you might get additional really good answers concerning Tools You Need to Install a New Bathtub .
Mounting a tub isn't specifically rocket science, yet it does call for strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bath tub with a new one is also a reasonably challenging project. If the old tub is conveniently easily accessible, the job can relocate rapidly; if you need to open a wall surface to get rid of the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to move out the old bathtub and also set in the new one. See to it you have actually qualified yourself for the job and also are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is better to think about using one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This post will certainly help you mount a new bathtub in your shower room if you have actually currently gotten a brand-new tub and do not need to transform the plan of your previous supply of water pipelines.
Your devices and also product list need to make up the following:
Preparing for the Installment
Firstly, the sustaining framework supplied with the bath should be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is separate the supply of water. After doing so, activate the taps to drain any water remaining in the system. The procedure of eliminating the existing faucets can be fairly troublesome due to the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the staying water that will come from the pipelines. Once the supply pipes have actually been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, place the tub in the called for placement. The wood boards are handy in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the tub until the spirit level reviews level.
To set up taps, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the water and also check all joints as well as brand-new pipework for leakages and also tighten them if required. Fill up the bathtub as well as additionally examine the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as defined in the maker's user's manual. Tiling and securing around the tub ought to wait until the bathtub has actually been utilized at the very least when as this will certainly settle it right into its final setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous type must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to crack a stiff seal, causing the water to permeate the wall between the bath as well as the tiling, leading to complications with moisture as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly load the tub with water before securing, to permit the movement experienced when the tub is in use. The sealant can fracture relatively very early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader on A Step-by-Step Guide to Installing a Bathtub, I think sharing that post was a good idea. Loved our piece of writing? Please share it. Help somebody else discover it. Thank you for your time spent reading it.
Quick, quality, call! Report this page